LEXUS RX 300

1998-2003 of release

Repair and car operation



Лексус RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Трансмиссионная a line
- Brake system
   The general information and security measures
   Removal, installation and check of pedals of brake system
   Check of brake system through a socket of the module of management
   Removal and installation of the tank and the main brake cylinder (ГТЦ)
   Removal, check and installation of the amplifier of brakes
   Replacement brake колодок
   Removal, dismantling, check, assemblage and installation of supports of brake mechanisms
   Dismantling, check and assemblage of a lay brake
   Check of the valve of distribution of brake effort
   Removal and installation of the activator of brakes
   Removal and installation of wheel gauges
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Basic schemes of electric connections


7bd329e4


Removal, check and installation of the amplifier of brakes

Components of installation of the vacuum amplifier of brakes

1 — the Collar
2 — the Vacuum hose
3 — the Lining
4 — the Vacuum amplifier

5 — Скоба
6 — the Returnable spring
7 — the Pin
8 — Шплинт
9 — the Holder

Check

 PERFORMANCE ORDER

  1. Squeeze out a pedal of a working brake some times at the switched off engine and make sure, that the pedal course does not vary.
  2. Squeeze out a pedal of a brake and start the engine. If the pedal slowly falls, the vacuum amplifier is serviceable.
  3. Start the engine and muffle it through 12 minutes. Slowly squeeze out a brake pedal some times. If the pedal is deeply pressed first time, and at the second or third attempt its course gradually decreases, the amplifier is tight.
  4. At the working engine squeeze out a pedal of a brake and, not releasing it, muffle the engine. Confirming to tightness of the vacuum amplifier the pedal should not change the a course in 30 seconds of its keeping.

Removal

 PERFORMANCE ORDER

  1. Remove ГТЦ (see Has undressed Removal and installation of the tank and the main brake cylinder (ГТЦ)).
  2. Disconnect from the vacuum amplifier a vacuum hose.
  3. Liberate from the holder (9 three tubes.
  4. Remove a returnable spring.
  5. Take шплинт and take out a pin.
  6. Give 4 nuts and remove скобу.
  7. Remove the amplifier together with a lining.

Installation

 PERFORMANCE ORDER

  1. Establish the amplifier with a new lining.
  2. Establish on an amplifier rod скобу.
  3. Tighten nuts of fastening of the amplifier with effort of 13 Nanometers.
  4. Insert a pin in скобу and a pedal of a working brake and fix it шплинтом.
  5. Establish a returnable spring of a pedal of a brake.
  6. Establish on ГТЦ a new lining.
  1. Establish on a lining the special adaptation and lower a core of the adaptation till the moment of a contact with the piston.
  1. Remove the special adaptation with ГТЦ and establish on the amplifier.
  1. Measure a backlash between a rod of the amplifier and a core of the special adaptation, - it should make 0 mm.
  2. Adjust a ledge of a rod of the amplifier so that its end slightly concerned a core of the special adaptation.

Adjustment make in the absence of the negative pressure enclosed to the amplifier (for this purpose at the muffled engine some times squeeze out a brake pedal to level pressure in the amplifier with atmospheric pressure).

  1. Establish ГТЦ, connect to the amplifier a vacuum hose, fix brake lines in the holder.
  2. Fill the tank with a brake liquid, pump over brake system and check up it on leaks.
  3. Adjust a pedal of a working brake (the Section Check and adjustment of a course of pedals of a working and lay brake see). Make a trial trip.