LEXUS RX 300

1998-2003 of release

Repair and car operation


Лексус RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Трансмиссионная a line
+ Brake system
- Suspension bracket and steering
   The general information
   + Forward suspension bracket
   + Back suspension bracket
   - Steering
      Checks of components of a steering
      Removal, installation, dismantling and assemblage of a steering column
      Removal and installation of pump GUR and it приводного a belt
      Removal, installation, dismantling and assemblage of the steering mechanism
   + Suspension bracket geometry
+ Body
+ Onboard electric equipment
+ Basic schemes of electric connections

7bd329e4


Removal, installation, dismantling and assemblage of a steering column

Components of installation of a steering column

1 — a steering wheel Overlay
2 — the Steering wheel
3 — the Screw with a head under прутковый a key
4 — Bottom заглушка №3 steering wheels
5 — Bottom заглушка №2 steering wheels
6 — Bottom подрулевая a plate of furnish of devices
7 — the Top section of a casing of a steering column
8 — the Block подрулевых switches with a spiral spring

9 — Assemblage of a steering column
10 — Assemblage of the steering hinge
11 — the Bottom section of a casing of a steering column
12 — the Collar
13 — Assemblage of №2 consolidations of an aperture for a steering column
14 — Assemblage of an intermediate shaft
15 — Bottom подрулевая the panel of furnish of the panel of devices
16 — the Bottom left lateral insert of furnish of the panel of devices
17 — the Lever of unlocking of the lock of a cowl

Components of assemblage of a steering column

1 — the Coil транспондера иммобилизатора the engine
2 — Assemblage of illumination of the lock of ignition
3 — the Switch of the prevention of extraction of a key from the ignition lock
4 — Э/м the valve of blocking of the ignition key
5 — the Cylinder of the lock of ignition
6 — the Amplifier транспондера
7 — the ignition Switch
8 — the Top arm of a steering column
9 — the Arm of the switch of indexes of turns

10 — Демпферная a plate
11 — the Latch демпфера
12 — Directing демпферной plates
13 — the Top holder of a steering column
14 — the Returnable spring of the lever of adjustment of an inclination of a steering column
15 — Bolts
16 — the Pipe of a steering column
17 — the Support of a pipe of a steering column
18 — the Bottom fastening of a pipe of a steering column

Removal and installation

 PERFORMANCE ORDER

  1. Establish wheels in position of rectilinear movement.
  1. Remove bottom заглушки №1 and №2 steering wheels and turn out bolts with heads of odes прутковый a key so that cuts in their heads have entered into an emphasis.
  1. Remove from a steering wheel an overlay, having separated a socket of electroconducting of a pillow of safety. Lay an overlay a face sheet upwards.

At socket separation at an ignition key finding in position ON or ACC in the management block the malfunction code registers.


Do not assort a steering wheel overlay.

  1. Separate a socket and turn out a nut of fastening of a steering wheel.
  2. Put adjusting labels on a steering wheel and on a steering shaft then remove a steering wheel.
  3. Verify two bolts, separate a socket, disconnect a cable of a drive of the lock of a cowl and remove bottom подрулевую the panel of furnish of the panel of devices.
  4. Turn out two bolts and remove the bottom left lateral insert of furnish of the panel of devices.
  5. Turn out three screws and remove the top and bottom casings of a steering column.
  6. Separate sockets подрулевых switches, a socket of a pillow of safety, turn out screws and remove assemblage подрулевых switches with spirally spring.
  7. Remove a spiral spring.

Do not assort a spiral spring and do not suppose hit on it of oil.

  1. Ослабьте a collar of assemblage of an intermediate shaft.
  1. Put adjusting labels on an intermediate shaft and a shaft of the steering mechanism, give a bolt A, turn out a bolt B and disconnect assemblage of an intermediate shaft.
  1. Remove bottom подрулевую a plate of furnish of devices, separate a socket, turn out adjusting nuts of a steering column and remove it.
  2. Turn out a bolt A and remove assemblage of an intermediate shaft with assemblage of №2 consolidations of an aperture for a steering column.
  3. Remove assemblage of №2 consolidations of an aperture for a steering column from assemblage of an intermediate shaft.
  4. Remove a collar.
  1. Put labels on the hinge and a shaft of a steering column.
  1. Turn out a bolt and remove assemblage of the steering hinge.
  2. Installation is made upside-down. Combine the adjusting labels put at removal, tighten fixture with demanded efforts.

Dismantling and assemblage

 PERFORMANCE ORDER

  1. Turn out the screw and remove the coil иммобилизатора and assemblage of illumination of the lock of ignition.
  2. Remove the top arm and the top holder of a steering column, having drilled 2 bolts.
  3. Turn out two bolts and remove an arm of the switch of indexes of turns.
  4. Remove a returnable spring of the lever of adjustment of an inclination of a steering column.
  5. Turn out a bolt, remove a washer and remove a support of a pipe of a steering column with the bottom fastening of a pipe of a steering column.
  6. Disconnect the bottom fastening of a pipe from a support.
  7. Remove latches демпферов, демпферные plates and their directing.
  8. Assemblage is made upside-down.