LEXUS RX 300

1998-2003 of release

Repair and car operation



Лексус RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
- Трансмиссионная a line
   The general information
   Removal and installation карданного a shaft
   Removal, dismantling, assemblage and installation of forward power shafts
   Removal, dismantling, assemblage and installation of back power shafts
   Replacement of a forward epiploon of back differential
   Replacement of lateral epiploons of back differential
   Removal and installation of the case of back differential, differential dismantling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Basic schemes of electric connections


7bd329e4


Removal, dismantling, assemblage and installation of back power shafts

Remarks in the beginning see Has undressed Removal, dismantling, assemblage and installation of forward power shafts.

Removal and installation

Components of a back power shaft

1 — power shaft Assemblage
2 — the Fixing cap
3 — the Pin
4 — the Lock ring
5 — Триподный the hinge

6 — the Gauge of speed ABS
7 — the Case триподного the hinge
8 — Protective covers
9 — Collars
10 — the Power shaft
11 — Пыльник №2


 PERFORMANCE ORDER

  1. Remove a corresponding back wheel.
  2. Turn out two bolts and remove back section of an exhaust pipe together with a lining.
  3. Turn out a bolt and remove the gauge of speed ABS.
  4. Take a pin, remove fixing cap and turn out ступичную a nut.
  5. Put labels on the case триподного the hinge and on a flange of back differential.
  6. Turn out 4 nuts, remove washers and disconnect a power shaft from differential.
  7. Remove a power shaft from the holder.
  8. Installation is made upside-down. Tighten fixture with demanded efforts, after installation check up serviceability of functioning of gauges ABS, and also check up and if necessary adjust corners of installation of back wheels.

Dismantling

 PERFORMANCE ORDER

  1. Check up power shafts:
    • External hinges should not have excessively big люфта;
    • Make sure of smoothness of movement of the internal hinge in a support direction;
    • Make sure of absence excessively big люфта internal hinges in a radial direction;
    • Check up protective covers on presence of damages.
  2. By means of a screw-driver remove collars of protective covers of hinges.
  1. Put labels on the case триподного the hinge and on a power shaft and remove the case of the hinge from a power shaft.

Do not use for drawing of labels a chisel.


  1. Remove a lock ring and put labels on триподный the hinge and on a power shaft.

Do not use for drawing of labels a chisel.

  1. Bring down a hammer and a pig from soft metal триподный the hinge from a power shaft.
  2. Remove protective covers with collars.
  3. The external hinge is not subject to dismantling.
  4. Fix a power shaft in a vice with soft sponges and by means of a screw-driver and a hammer bring down from a shaft пыльник №2, trying not to damage a rotor of the gauge of speed ABS.

Do not damage a rotor of the gauge of speed ABS.

Assemblage

 PERFORMANCE ORDER

  1. Напрессуйте new пыльник №2 on a shaft.
  1. Temporarily establish new covers of hinges with collars.

Before installation of protective covers wind шлицы a power shaft with a vinyl tape to prevent their damage.

  1. Place on a power shaft триподный the hinge конусной a part to the external hinge and level adjusting labels of the hinge.
  2. Напрессуйте the hinge on a power shaft by means of a hammer and a pig from soft metal. Establish a lock ring.
  3. Fill in a cover of the internal hinge 180 190 г yellow greasing, level adjusting labels of the case of the hinge and fix the case to differential.
  4. Fill in a cover of the external hinge 107 117 г grey greasing.
  1. Make sure, that covers come into grooves on приводном to a shaft and are not deformed at standard length of a shaft.
  1. Fix protective covers collars, having tightened their screw-driver.