LEXUS RX 300

1998-2003 of release

Repair and car operation



Лексус RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
- Options and car routine maintenance
   The general information
   The general data on options and adjustments
   The routine maintenance schedule
   Check of levels of liquids, the control of leaks
   Check of a condition of tyres and pressure of their rating, rotation of wheels
   Replacement of impellent oil and the oil filter
   The general checks of brake system
   Check and replacement салонного the filter of a heater and К/В
   Check of a condition and replacement of hoses of an impellent compartment, localisation of leaks
   Check of a condition and replacement of belts of a drive of auxiliary units
   Replacement of a filtering element of an air cleaner
   Check of a condition of system of release of the fulfilled gases
   Check and replacement of spark plugs
   Replacement of a brake liquid, prorolling of brake system
   Check of a condition of components of a suspension bracket and steering
   Check of a condition of protective covers of power shafts and hinges карданного a shaft
   Check of working capacity of lighting devices, horn and the heater fan
   System EVAP check
   Condition check, adjustment and replacement of brushes of screen wipers
   Check of a condition of the battery and care it
   Replacement of a cooling liquid (ОЖ)
   Check and adjustment клапанных backlashes
   Check and adjustment of a course of pedals of a working and lay brake
   Check of boots of a lay brake
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Basic schemes of electric connections


Replacement of impellent oil and the oil filter

Long contact of a skin to the fulfilled impellent oil is dangerous enough. Use a protective cream or put on rubber gloves during carrying out described below procedures.


Frequent replacement of impellent oil is the main preventive procedure of service accessible to the mechanic-fan. Eventually oil is subject разжижению and to pollution that conducts to premature deterioration of the engine.

Спускание impellent oil

Impellent oil can be pumped out by means of a probe through directing tube щупа.


 PERFORMANCE ORDER

  1. Warm up the engine to working temperature of a cooling liquid.
  2. Поддомкратьте the car also establish it on props, or tyre out on a viewing hole.
  3. Substitute under a drain stopper capacity in volume about 6 l for gathering of the fulfilled oil.
  1. Turn out a drain stopper and allow to oil to flow down completely.

Do not burn a hand разогретым following oil!

  1. Check up a condition of the fulfilled oil. If in it there is at a considerable quantity a metal shaving and deterioration products, it specifies in presence задиров, for example, in bearings of a cranked shaft and шатунных bearings. For an exception of damages after the spent repair it is necessary to clear carefully oil channels and hoses, and also, at a corresponding complete set, to replace маслоохладитель.

Replacement of the oil filter

 PERFORMANCE ORDER

  1. Turn out the oil filter from a flange. For this purpose it is possible to take advantage of the special adaptation or a tape key. It is possible to insert also a sharp screw-driver sideways into the filter, thus oil will start to follow from the filter, therefore in advance substitute capacity for oil gathering under the filter.
  1. Wipe a surface of the oil filter and its flange on the block of cylinders and remove a sealing lining if it remained on a flange.
  2. Grease a sealing lining of the new oil filter with pure impellent oil.
  3. Screw the new oil filter by hand. After the lining will lie down to a flange on the block of cylinders, tighten the filter on three quarters of a turn. Pay attention to the remarks resulted on the case of the filter.

Refuelling of the engine by oil

At replacement it is necessary to use oil of identical type and, whenever possible, identical mark. For this purpose it is recommended to fix at each replacement of oil by the engine a label with instructions of mark and viscosity of oil. Impellent oils of identical type and identical marks, but different viscosity can fill in during a corresponding season.


 PERFORMANCE ORDER

  1. Screw a carving stopper of a drain aperture with a new sealing ring and tighten it with effort of 45 Nanometers.
  2. Remove a cover of a jellied mouth and fill in impellent oil approximately on half-litre less, than it is specified in Specifications (the Section Check of levels of liquids, the control of leaks see).
  3. Start the engine and allow to it to work idling, having checked up in the meantime presence of leaks of impellent oil.
  4. Wait for 5 minutes, then check up level of oil and if necessary modify it.
  5. Make a trial trip on the car and check up a drain stopper and the oil filter on leaks. If necessary, cautiously tighten them. Once again check up oil level, if necessary modify it.





7bd329e4